Downloads

Downloads

Optibox C-1000

High Definition Cable Receiver - Conax Embedded

MAIN FEATURES

  • High Definition Digital Cable Receiver with Conax Embedded
  • User friendly, multilangual OSD
  • USB2.0 connection support for data transfer
  • 576p, 720p, 1080i support
  • Electronic Program Guide (EPG)
  • Easy and Fast auto programming
  • S/PDIF output for Dolby Digital audio output
  • 4 digit LED display
  • Display for service number and time display
  • Support for JPEG and MP3 files
  • Software upgrade by USB or Over The Air

TECHNICAL SPECIFICATIONS

Tuner & Demodulator

RF Input Range:
VHF Low CH.E2 ~ CH.S6 ( 50.5MHz ~ 142.5MHz )
VHF High CH.S7 ~ CH.S36 (149.5Mhz ~ 426.0MHz)
UHF CH.S37 ~ CH.E69 (434.0Mhz ~ 858.0MHz)

Input Connector: IEC-DIN(IEC 169-2) Female
Output Connector: IEC-DIN(IEC 169-2) male (With Loop-Through Output)
Input/Output Impedance: 75[Ohm],Unbalanced
Signal Input Level at QEF:
-20 ~ -67 dBm at (64QAM, SR=6.875Msps)
-20 ~ -64 dBm at (128QAM, SR=6.875Msps)
-20 ~ -61 dBm at (256QAM, SR=6.875Msps)
PLL X-tal Frequency: 4 Mhz
Intermediate Frequency: 36.125 Mhz(Center)
IF Bandwidth: 8MHz
QAM Demod-IC TDA10023(NXP)
FEC Annex A/C
Modulation Format: 16, 32, 64, 128, 256 QAM
Symbol Rate: 1.0 Msps ~ 7.0 Msps
Roll-Off Factor: 0.13, 0.15

Supporting System -. Compliant Nordig Unified 1.0.3.
-. European digital cable standard ETSI EN 300 429 & Cable Ready.
-. Loop-Through output(Full band) Compliant with Cable Ready

MPEG TS A/V Decoding
Transport Stream Format: MPEG-2/MPEG-4 Part10 AVC/H.264 HD HP@L4.0 1920x1080 @ 50Hz
(MPEG-2 ISO/IEC 13818 Transport stream Specification)
Profile Level: “MPEG-2 MP@HL”, MPEG-4 Part10 AVC/H.264 HD MP@L4.0
Input Rate: Maximum 31.668450Mb/s, 27.709893Mb/s
Video Aspect Ratio: 4:3, Letter Box, 16:9, Pan & Scan
Video Display Resolution: 1920x1080i, 1280x720p, 720x576p, 720x576i @ 50Hz
Audio Decoding Format: MPEG-1 Layer 1,2, Dolby AC-3(Pass-Through)
PCM with Decoded Stereo AAC Stereo
Audio Output Mode: Mono, Left, Right, Stereo, Dolby Digital bit-streams
A/V And Data Output

Analog Component YPbPr: 1 Set(3xRCA Vertical Array Type)
CVBS(Composite Video): 1 Jack(RCA Type)
S/PDIF Dolby Digital Interface: 1 Optical(Fiber Optic Type)
Stereo Audio: L/R 1 Set(2xRCA Array Type)
HDMI/HDCP 1 HDMI™ Connector
SCART Interface: TV/VCR(CVBS, RGB)
USB2.0 Host Interface: A-Type Horizontal Connector (Firmware Upgrade Port)

Conditional Access Interface
Smart Card Reader: 1 Slot For Embedded CAS Support
(Conax CAS v7 Embedded)
PCMCIA: N/A

System Resource Information
Main Processor: ST40 32-bit Superscaler RISC CPU_400 Dhrystone 2.1
MIPS@266MHz
Flash ROM: Default 8Mbytes(Secure Flash)
Program & Graphic DDR SDRAM Default 128Mbytes(Program 64Mbytes & Graphic 64Mbytes)
Serial EEPROM: Default 128Kbits

Power Supply
Input Voltage: AC 100-240V ~ 50/60Hz
Power Consumption: Maximum 20Watts(Under 2Watts in Standby Mode)

1) Active Stand-by Mode: Press the Stand-by button on RCU/Front Panel shortly to enter this mode.

2) Passive Stand-by Mode: Press the Stand-by button on RCU/Front Panel for 2~3 sec to enter this mode.

Protection: Separate Internal Fuse
Type: SMPS(Switching Mode Power Supply)
Safety And EMI: For Country Regulation

Physical Specification
Dimension(WxDxH): 260x180x55[mm]
Net Weight: About 2.0Kg
Operation Temperature: 5°C ~ 50°C
Storage Temperature: -40°C ~ 65°C